MPEG Toolkit

home *** CD-ROM | disk | FTP | other *** search

/ MPEG Toolkit / MPEG Toolkit.iso / dos / display / drvsrc / newss24x.asm < prev next >

Wrap

Assembly Source File | 1997-01-01 | 14.3 KB | 404 lines

;-------------------------------------------------------------------------- ; This is file NEW24X.ASM ; ; Copyright (C) 1993 Denis Bos, Einsteinstr 37, 6533 NG ; Nijmegen, The Netherlands ; ; Just kidding about the copyright, but the adres is correct ; ; A friend of mine (actually a roomy) had the 'normal' version of ; this driver, but it didn't work for 24-bit, so I looked at a few ; drivers and the book (that came with the Speedstar 24x), and came ; up with this driver, which looks remarkebly the same as the 'nor- ; mal' version (ss24x.asm), but with an additional mode for 24-bit ; ; I hope it works with all the other modes as well, haven't had time ; to test them all (just most of the graphics-modes). ; ; This file is distributed WITHOUT ANY WARRANTY; without even the implied ; warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. (??!) ; ; I added the 24-bit mode (mode 72h) support on 24-10-93 ; Compiled with MASM it should work (it did on my computer) ; ; PS2: I removed the req_... stuff, because i didn't have any (include) ; file in which was described what val_... was, but I don'd think those ; modes are that important. 24-bit is!! (You probably can just add them ; again..) :-) ;-------------------------------------------------------------------------- .386 include grdriver.inc cseg segment byte public use16 'code' assume cs:cseg, ds:cseg, es:cseg, ss:nothing ;-------------------------------------------------------------------------- ; DRIVER HEADER ; The following entries MUST match the structure and constant ; declarations in the file 'grdriver.h' of the GRX graphics library ; The mode word should contain the following bitfields: ; - the GRD_NEW_DRIVER bit set for any new format driver ; - the adapter type field should be specified ; - the memory size field should be specified ; - the paging mode field should be specified ; The mode set routine will OR in the plane bitfield as it will ; change when different color number modes are requested. ;-------------------------------------------------------------------------- dw offset mode_set_routine dw offset paging_routine mode_W dw GRD_NEW_DRIVER+GRD_VGA+GRD_1024K+GRD_RW_64K ; ; The 'def_xx' fields are filled in by go32 from the corresponding ; fields of the 'GO32' environment variable ; def_tw dw 80 ; text width def_th dw 25 ; text height def_gw dw 640 ; graphics width def_gh dw 480 ; graphics height def_nc dw 16 ; graphics colors dw offset driver_init_routine dw offset text_mode_table dw offset graphics_mode_table ; ; Biggest text and graphics sizes ; Max_TW equ 132 Max_TH equ 50 Max_GWn equ 1024 ; non interlaced!!! Max_GHn equ 768 Max_GW equ 1280 ; may be interlaced Max_GH equ 1024 ;-------------------------------------------------------------------------- ; TABLE OF SUPPORTED TEXT MODES ; - keep sorted by size ; - end with an all 0 entry ; - BIOS field = 0xff disables it ; - fields: ; width, height, colors, BIOS#+ setup_procedure_index*256 ;-------------------------------------------------------------------------- text_mode_table label word dw 80, 25, 2, 007h + 00000h dw 40, 25, 16, 001h + 00000h dw 80, 25, 16, 003h + 00000h dw 80, 34, 16, 041h + 00000h dw 80, 43, 16, 067h + 00000h dw 80, 50, 16, 066h + 00000h dw 132, 25, 16, 055h + 00000h dw 132, 28, 16, 047h + 00000h dw 132, 43, 16, 054h + 00000h dw 132, 44, 16, 021h + 00000h dw 132, 50, 16, 069h + 00000h dw 0, 0, 0, 000h + 00000h ;-------------------------------------------------------------------------- ; TABLE OF SUPPORTED GRAPHICS MODES ; - keep sorted first by colors then by size ; - end with an all 0 entry ; - BIOS field = 0xff disables it ; - fields: ; width, height, colors, BIOS#+ setup_procedure_index*256 ;-------------------------------------------------------------------------- graphics_mode_table label word dw 320, 200, 16, 00dh + 00000h dw 640, 200, 16, 00eh + 00000h dw 640, 350, 16, 010h + 00000h dw 640, 480, 16, 012h + 00000h dw 800, 600, 16, 058h + 00000h dw 1024, 768, 16, 05dh + 00000h dw 1280, 960, 16, 06ch + 00000h dw 1280, 1024, 16, 064h + 00000h dw 320, 200, 256, 013h + 00000h dw 640, 400, 256, 05eh + 00000h dw 640, 480, 256, 05fh + 00000h dw 800, 600, 256, 05ch + 00000h dw 1024, 768, 256, 060h + 00000h dw 640, 480, 32768, 062h + 00000h dw 800, 600, 32768, 063h + 00000h dw 640, 480, 0c018h, 072h + 00000h ; The extra mode dw 0, 0, 0, 000h + 00000h ;-------------------------------------------------------------------------- ; TABLE OF SPECIAL SETUP PROCEDURES ; You may need such procedures for: ; -- reloading fonts on standard EGA or VGA for ; higher resolution text modes ; -- enable HiColor mode of some Super VGAs ; -- Handle the parameter passing conventions of the VESA BIOS ; -- put VGA into 256 color plane mode ("MODE X") ; -- etc... ; There should be one entry in the table for every non-zero ; 'setup_procedure_index' in the text and graphics mode tables. ; The first entry in the table belongs to index 100h, and so on. ; The special setup procedure is invoked via a near call. ; ; Entry: DI=address of the mode record from the text or graphics ; table to set up. ; ; Exit: Adapter configured ; BX=driver mode word as it should be returned by the mode set ; routine. Typically it involves picking up the mode word ; from the header and OR-ing in the appropriate bitplane mode ; bitfield. (This is not needed for text modes) ; AX, CX, DX, SI can be trashed, PRESERVE DI!!!! ; ; NOTE: This runs in real mode, but don't mess with the segment registers. ;-------------------------------------------------------------------------- special_setup_table label word dw offset VGA_50row_mode_set ; ; Routine to set up VGA 50 row mode ; interface is described above ; VGA_50row_mode_set proc near mov ax,03h ; set 80x25 mode int 10h xor bx,bx mov ax,1112h ; load 8x8 font int 10h ret VGA_50row_mode_set endp ;-------------------------------------------------------------------------- ; DRIVER INIT ROUTINE ; called once after the driver is loaded ; may do one or more of the followings: ; - check for proper board type ; - check amount of RAM on board, and: ; -- update word in header to reflect correct amount ; -- disable modes in the tables for which there is not enough RAM ; - check for special equipment (HiColor DAC, etc...) ; ; Entry: nothing ; ; Exit: AX=status: ; non-zero: OK, ; 0: something went wrong (e.g. wrong adapter, etc..) ; BX,CX,DX may be trashed ; ; NOTE: This runs in real mode, but don't mess with the segment registers. ;-------------------------------------------------------------------------- driver_init_routine proc far mov dx,03ceh mov ax,0e0bh out dx,ax ; enable second bank register mov dx,03c5h mov ax,0ff11h ; set bank registers for R/W banking out dx,ax ; at B000:0000 - B000:FFFF ret driver_init_routine endp ;-------------------------------------------------------------------------- ; MODE SET ROUTINE ; sets up a text or graphics mode as close as possible to the one ; reguested by the user with regard to number of colors and size. ; ; Entry: AX=mode selection ; 0 = 80x25 text ; 1 = default text ; 2 = text CX cols by DX rows ; 3 = biggest text ; 4 = 320x200 graphics ; 5 = default graphics ; 6 = graphics CX width by DX height ; 7 = biggest non-interlaced graphics ; 8 = biggest graphics ; 9 = graphics BX colors, CX width by DX height ; ; Exit: BX=driver mode flag ; CX=width (in pixels or characters) ; DX=height ; ; NOTE: This runs in real mode, but don't mess with the segment registers. ; YOU SHOULD NOT NEED TO CHANGE THIS ROUTINE AS IT IS PRETTY ; MUCH TABLE DRIVEN ;-------------------------------------------------------------------------- mode_set_routine proc far push ds push di push si mov si,cs mov ds,si cmp ax,9 jbe DoIt jmp Exit DoIt: add ax,ax mov si,ax jmp WORD PTR mode_set_table[si] mode_set_table label word dw offset mode_0 dw offset mode_1 dw offset mode_2 dw offset mode_3 dw offset mode_4 dw offset mode_5 dw offset mode_6 dw offset mode_7 dw offset mode_8 dw offset mode_9 mode_0: mov si,offset text_mode_table ; 80x25 text mov bx,def_nc mov cx,80 mov dx,25 jmp Lookup mode_1: mov si,offset text_mode_table ; default text mov bx,def_nc mov cx,def_tw mov dx,def_th jmp Lookup mode_2: mov si,offset text_mode_table ; CX*DX text mov bx,def_nc jmp Lookup mode_3: mov si,offset text_mode_table ; biggest text mov bx,def_nc mov cx,Max_TW mov dx,Max_TH jmp Lookup mode_4: mov si,offset graphics_mode_table ; 320x200 graphics mov bx,def_nc mov cx,320 mov dx,200 jmp Lookup mode_5: mov si,offset graphics_mode_table ; default graphics mov bx,def_nc mov cx,def_gw mov dx,def_gh jmp Lookup mode_6: mov si,offset graphics_mode_table ; CX*DX graphics mov bx,def_nc jmp Lookup mode_7: mov si,offset graphics_mode_table ; biggest non-interlaced gr mov bx,def_nc mov cx,Max_GWn mov dx,Max_GHn jmp Lookup mode_8: mov si,offset graphics_mode_table ; biggest graphics mov bx,def_nc mov cx,Max_GW mov dx,Max_GH jmp Lookup mode_9: mov si,offset graphics_mode_table ; CX*DX graphics w/ BX colors ; ; At this point: ; SI points to the table to search (text or graphics) ; BX has colors ; CX has width ; DX has height ; Lookup: xor ax,ax ; last color number seen Find_C: cmp [si+4],ax ; last color number == this? je Same_C jb Prev_C ; end of table -- use last color cmp BYTE PTR [si+6],0ffh ; valid entry ? je Prev_C ; not -- use last color mov ax,[si+4] ; record color number mov di,si ; start of entries w/ this color cmp ax,bx ; enough colors ? jae Find_S Same_C: add si,8 jmp Find_C Prev_C: or ax,ax ; found any color at all? je Exit ; ; At this point: ; DI points into the table to the first entry with the desired color ; number (either it has enough colors or it is the highest color ; number supported by the driver). Additionally, at least the ; first (= smallest size) entry for this color is valid (has a ; valid BIOS number). ; AX has the color number adjusted for the driver ; CX has width ; DX has height ; Find_S: cmp [di+4],ax ; still the same color #? jne Prev_S cmp BYTE PTR [di+6],0ffh ; valid entry ? je Prev_S cmp [di],cx jb Next_S cmp [di+2],dx jae GotIt Next_S: add di,8 jmp Find_S Prev_S: sub di,8 ; ; At this point: ; DI points to the table entry we want to set up ; GotIt: mov ax,[di+6] ; BIOS mode number or ah,ah ; special ? je doBIOS mov al,ah xor ah,ah dec ax add ax,ax mov si,ax call WORD PTR special_setup_table[si] jmp RetVal doBIOS: int 10h mov bx,GRD_1_PLANE cmp WORD PTR [di+4],2 ; 2 colors ? je doFLAG mov bx,GRD_4_PLANES cmp WORD PTR [di+4],16 ; 16 colors ? je doFLAG mov bx,GRD_8_PLANES cmp WORD PTR [di+4],256 ; 256 colors ? je doFLAG mov bx,GRD_16_PLANES cmp WORD PTR [di+4],32768 ; 32K colors ? je doFLAG mov bx,GRD_24_PLANES cmp WORD PTR [di+4],0c018h ; 16M colors ? je doFLAG mov bx,GRD_PLANE_MASK ; something is wrong!! doFLAG: or bx,mode_W RetVal: mov cx,[di] mov dx,[di+2] Exit: pop si pop di pop ds ret mode_set_routine endp ;-------------------------------------------------------------------------- ; PAGING ROUTINE ; ; Entry: AH=read page ; AL=write page ; ; Exit: VGA configured. ; AX,BX,CX,DX,SI,DI may be trashed ; ; NOTE: This runs in protected mode! Don't mess with the segment registers! ; This code must be relocatable and may not reference any data! ;-------------------------------------------------------------------------- assume ds:nothing, es:nothing paging_routine proc far mov cl,4 shl ah,cl ; WD90C3x offset registers have 4k granularity shl al,cl ; => multiply by 16 to get normal VGA 64k bank granularity mov bh,al mov bl,0ah ; write bank gets PR0B index code mov al,09h ; read bank gets PR0A index code mov dx,03ceh ; load graphics index register number out dx,ax ; set PR0A (read bank) mov ax,bx out dx,ax ; set PR0B (write bank) ret paging_routine endp cseg ends end